How easy it is to make "American turn signals" with your own hands. "American dimensions" do it yourself Additional cartridge in the headlight

Manufacturing process:

Step one. Device diagram
The scheme of the system is very simple, there is practically nothing to describe here. All that needs to be done is to connect the elements in a certain order to the gap between the turn signal lamps and the power supply. When operating in size mode, power must be supplied to a single wire. The author didn’t connect the dimensions directly to the turning lights, he made a separate button to turn on the "American women" if necessary. For these purposes, the fog light button was used.

Step two. Relay connection process
The relay is connected by soldering. How to do this can be seen in detail in the photo. The most important thing in this process is the careful isolation of the soldered area and exposed conductors.

Step three. We connect the button and test the system
Now it remains to connect the system to the block on-board computer, connect the button, the author even connected the power indicator. Now, after pressing the button, it starts to glow, which indicates that the system is turned on. Well, how everything works, you can see in more detail on the video.

Kind time of the day, dear readers, the other day I was on fire to make my car a little American, and decided to make the dimensions in the turn signals, there are not many options for such an operation, for example: 1) Embed the second base and power it from the factory dimensions, but such a manual is not mine suited, tk. when the turn signal is turned on, it burns brighter and dimmer.

2)— Put a two filament light bulb (it is difficult that two filament light bulbs of yellow color are hard to find, and besides, the result is the same as in the first version.

3)— the option that I chose, and the most difficult (creating two modes of rotary lamps using a 5-pin relay, a diode and a capacitor). I will try to tell you about all my actions.

First of all, we go to the electrical parts store and buy there:

1. A capacitor for 4700 uF * 25v or 3000 uF * 25V or 3300 uF * 25V I don’t know what the difference is, it seems like in capacity, I used 4700 uF * 25v in total - 2pcs.

2. Diode 5817 or 5819, I also don’t know what is the difference, I took 5817
3. Relay 5-pin conventional automobile - 2 pcs.
3. Terminals for relays - 2 pcs.
4. Round terminals - 2 pcs.
5. Wire - 4m. (colored) I took by colors as in the diagram
6. Electrical tape or heat shrink
7. Terminals mum

young electrician's set

Then we take the scheme and begin to collect everything exactly according to the scheme

After you have done your homework) we go to the car, remove both headlights and look for “+” from the dimensions and “+” from the turn signals. The turn signal has only 2 wires, the color will be a plus, and the plus from the size will be in the upper right corner of the chip. And again, guided by the scheme, we begin to twist the wires.

Then we connect the “-” in any convenient place. Well, that's it.

There are many tuning methods, the cheapest of which is headlights. In addition to the elementary replacement of low and high beam bulbs, motorists are often interested in how to make the dimensions in the turn signals. Some drivers even duplicate the side light on the VAZ 2110 or VAZ 2114. This is done due to the not very good visibility of the lighting on the road surface, which is very important at night and in bad weather to prevent accidents.

Types of jobs

You can modify the turn signals on a car in the following ways:

• to supplement the burning turn signals with dimensions by moving them from the headlights;
• insert additional side lamps on the front optics;
• change the color of the side lamps to yellow or white;
• use .

If the dimensions are yellow, then the light from the turn signals will merge with it, if the color is white, then the turn signals will stand out against the background of the main dimensions

Installation process

Before you understand how to connect the turn signals to the dimensions, please note that there are two main colors of the side lights optics:

• yellow ("American") with the same color of the rotary optics will merge;
• white with a yellow turn color is better to stand out on the road.

Parking lights are inserted into turn signals on cars as follows:

• in the rotary optics on the VAZ, cut a hole where the cartridge will be inserted. The cartridge type w5w can be used. It will be inserted into a standard 5W incandescent bulb or LED strip;
• fix the cartridge in the optics for rotation in order to avoid moisture, dirt and for durable fastening;
• to transfer the lighting from the headlights to the VAZ 2107 or 2109, switch the wires to the newly mounted socket. When connecting additional lights without transfer, it is required to close the contact in the block that goes to the headlamp in a parallel manner.

A car after such a revision acquires a special charm.

Despite the apparent convenience for the driver, according to the Code of Administrative Offenses, such a configuration change leads to confusion for other drivers and even causes accidents.

Also note that if you install lighting devices in front of the car, equipped with red lights or reflectors, as well as devices with an inappropriate operating mode and color, you face a fine in the following amounts:

• 2500 rubles if you are a civilian;
• 15,000-20,000 rubles - official;
• 40,000-50,000 rubles - legal.

Penalties are regulated by the regulation on the admission of cars to use.

Recently, motorists have resorted to the opportunity to equip side lighting in corners by means of bulbs with two contacts. But this measure can also prevent other participants road traffic... Thus, manipulating the headlights, however helpful they are, can compromise your safety. Therefore, do not be surprised at the increasing attention to your car from the traffic police.

Many people want to improve the front optics, because with good light driving is much more comfortable and safer for you, as long as your light does not interfere with oncoming drivers. There are many ways to do this. But some want to get a unique and unusual look due to headlight tuning. To do this, for example, they install additional dimensions in the turn signals or completely transfer them there, creating the so-called American style.

The American style lies in the fact that the dimensions are constantly on, their bulbs are in the turn signals and most often they are orange.

American women on VAZ 2114 are a very frequent practice, with them the car really looks more interesting, in addition, in the dark, any additional light will not interfere. With poor visibility, a car with this tuning is more noticeable on the road. But you need to understand that such a change can mislead other road users and sometimes it becomes the cause of an accident.

Yellow dimensions merge with turn signals, and some road users may misjudge the situation. Therefore, it is better to use white dimensions, then the orange turn signals will stand out clearly.

The attention of traffic police officers to a car with such a modification is increased, and it is possible that you will be stopped more often to check your documents.

Making American vaz 2114 everything must be done within the law, there are clear restrictions on any changes to the front optics. For example, it is definitely impossible to install red lamps, reflectors and any other devices with an inappropriate color and mode of operation. For such violations, a fine of 2,500 rubles was imposed.

How to make American women on a VAZ 2114

There are many ways to sell American women on a VAZ 2114, each has its own pros and cons. Depending on your skills, desires and capabilities, you can choose any of the ones presented below, or come up with your own.

Turn signal lamp with two threads.

A double-strand lamp is a relatively good method. It is quite easy to install and straightforward to use. There are two filaments in the lamp, one dim for 5 watts, the other brighter for 25 watts. A thread with a weak brightness is used as side lights, and with a strong one for turn signals. As a result, the turn signal is quite clearly noticeable against the background of the side lights.

For installation, you need a base for two +, or solder the wire directly to the lamp, but you need to be careful, as it may burn out.

Relay

Signal inversion principle. In this case, the turn signal lamp is constantly on when driving, and when the turn signal is turned on, it starts blinking. In terms of brightness, as in the previous case, the lights do not differ, but a signal is highlighted due to the fact that the lamp completely extinguishes at the time of operation.

Installation is simple, you just need to cut the wires a little and two five-pin relays, one for each headlight.

Relay with capacitor and diode

This method, in fact, is more correct than the previous one. An IN5819 diode and a 25 volt 4700 mF capacitor are added to the five-contact relay. The principle of operation is the same, but there is a guarantee that nothing will close anywhere and will last a long time without problems.

Closing the dimensions to the turn signal lamp

There is nothing easier how to close the turn signals on the VAZ 2114. But this method is fundamentally wrong, and it is strongly discouraged to use it. The turn signal lamp is directly connected to the dimensions, and the turn signal is essentially absent at all.

Additional cartridge in the headlight

The most correct, in the opinion of the majority, but at the same time the most labor-consuming method, is the introduction of an additional cartridge into the headlight. The cartridges are taken from unnecessary repeaters, cut off and soldered into the headlight. With careful execution, everything looks imperceptible, not everyone will guess about the changes made.

Useful video

You can get additional information on setting the dimensions in the turn signals from the video below: